4-Stroke Engine Playlist
Subscribe to my channel« Prev1 / 2Next »Why to replace cylinder studs. Have you put much thought into what you reuse?How to...more
Why to replace cylinder studs. Have you put much thought into what you reuse?
How to safely remove a flywheel rotor. The "Old Boy" method!
Part 2: Did the Marvel Mystery Oil trick work after 800 plus miles or did we bust a myth?
Part 1: Does the Marvel Mystery Oil trick REALLY work to raise low compression?
How to test for an exhaust leak! 100% verification!
How to replace an oil seal with the shaft still in the case.
How To Change Motorcyle Connecting Rod Kit Crank As | Cara Mengganti Setang Seher Motor
How to remove a valve that won't pull through the head
How to pull a piston wrist pin Motion Pro Deluxe P/N 08-0472
Part 2 : How to do a cylinder leak down test with SMOKE to "see" the loss.
Part 1: How to do a cylinder leak down test to "hear" the loss. Traditional Method
How to do a compression test. BONUS TIP: How to test the tool! Demo on: DRZ400 Engine Test
Trick methods for holding the cam chain tensioner in place for removal or installation.
How to properly time and wind your kickstart on assembly!
How to fit a piston pin with craftsmanship. Are you a mechanic, technician or craftsman?
How to fix a gasket hole that doesn't line up and how to make your own gaskets holes perfect!
Do you have stuck dowel pin in the opposite case? Tip for supporting the gasket!
How not to ruin your crankshaft when pulling the rotor!
Which bolts go where? How to verify long and short bolt location!
Watch what happens to compression from a mis-timed YZ250F Hot Cams camshaft by just one tooth!
How to "actually" torque the valve adjuster locknut on threaded screw type
How to get a "feel" for the correct feeler gauge when adjusting valves-thread type valve adjusters
How to check oil level on a YZ250F Similar procedure to check oil level on most Dry Sump Oil Systems
How to start yz250f (short version 2 min) cold and hot start. FULL 6 min version link below!
How to cold start and hot start a YZ250F in 6 min FULL detailed video!
How to time your camshafts correctly. The most common human error made shown on close up video!
Why is it important to understand top dead center vs. overlap on a 4-stroke? #DOHC #how2wrench
DIY: Suzuki Vstrom How to change your oil and filter
Part 2: How to measure, select and adjust the clearances. TIP: How to do it on bench before install!
Part 1: Why you MUST use a micrometer to measure valve shims and NOT a vernier caliper!
How to apply sealant to assemble any case or cover. BONUS: What you didn't know and wished you did!
How to install piston rings and not break them BONUS: oil ring explanation POV installation!
How to install cylinders found on Motorcycle Atv Sled Watercraft Harley Dirt #motorcyclecylinder
How to install piston pin clips close up! Bonus teaching of "how not to install" included!
How to perform a cylinder leakdown test: Demo on Harley Shovelhead EVO TWIN CAM
EM Series: The why behind copper exhaust gasket direction of installation
Every Mechanic Series: How to time & install DOHC motorcycle atv camshafts
EVERY MECHANIC SERIES: How to install crankshaft transmission oil seal and installation tips
Installing bearings with dry ice
How to Install Piston Pin clips Alternative Method
4 Stroke Engine Assembly Clutch 12 16 14
2 Stroke Engine Disassembly Cylinder Stud Removal 11 17 14
Old Boy Trick: How to fix leaking valves using wood.
2 Stroke Engine Assembly: How assemble the crankcases
2 Stroke Engine Disassembly Bearing Removal from Shaft Puller Method 11 04 14
2 Stroke Engine Disassembly Oil Seal Removal Seal Puller Method 11 03 14
2 Stroke Engine Disassembly Dowel Pin Removal 10 30 14
2 Stroke Engine Disassembly Blind Bearing Removal 11 03 14
2 Stroke Engine Disassembly & Assembly Bearings & Oil Seals 11 03 14